Questions? Call us: 800-547-1539 | Fax: 800-547-1535 | Contact Us ›
Adding to cart

Penco Lift and Plastic Trigger for Recessed Locker Handle Assembly, RH, Gray

Penco Lift and Plastic Trigger for  Recessed Locker Handle Assembly, RH
Sku: PN-333R
Price: $8.27

Shipping calculator estimates the cost of delivery at the time of processing. Costs may vary depending on additional services requested and based on the destination and shipping method. For expedited shipping options and costs for additional services provided by freight carriers, please contact us at 800-547-1539.
Replacement right hand lift for the Penco recessed locker handle PN-3331. Includes plastic trigger.
  • Material
  • Lift: Steel
  • Trigger: Plastic
  • Thickness: 5/64" (between 1/16" and 3/32")
  • LIFT
  • Back side
  • Height: 4-1/4"
  • Width of back plate (measurements taken from the back)
  • At top: 2-3/32"
  • At middle: 23/32"
  • At bottom: 1-1/8"
  • There is a tab at the bottom, which is bent to the back
  • at a 90o angle
  • Height: 21/32"
  • Depth: 1/2"
  • Side that mounts to the lockbar. There is a shorter front half
  • and a taller back half, both, combined are the same height as
  • the back of the lift.
  • Front half
  • Height, not including finger tab: 2-5/16"
  • Width: 11/16"
  • Finger tab (fits into lockbar)
  • Height: 13/32"
  • Width
  • At the base: 5/32"
  • At the tip: 9/64" (Between 1/8" and 5/32")
  • The tab is bent out and up, to fit into a hole in the
  • lockbar. The distance between inside of the tab
  • and the outside wall of the lift
  • At base of bend: 3/32"
  • AT tip of finger: 1/8"
  • Mounting hole
  • Qty: 1
  • Dia: 3/16"
  • Distance from bottom of the lift to the center of
  • the mounting hole: 9/32"
  • The front half of the side fo the lift is offset to just
  • outside the back half
  • Offset amount: 1/16"
  • Back half
  • Height: 4-1/4"
  • Depth: 21/32"
  • Finger lift side
  • Top portion - a horizontal tab
  • Depth: 1-3/16"
  • Height: 3/4"
  • Lower portion - a tab that extends vertically down from
  • the top portion. The PN-333T plastic trigger has a
  • slot in it's middle which slides over and is mounted onto
  • this portion.
  • Depth: 3/4"
  • Height: 9/16"
  • Padkick hole dia: 3/8"
  • Height of top and lower portions combined: 1-5/16"
  • Plastic trigger (PN-333T). The top third is wider than
  • the lower two thirds. In addition, there is a rounded
  • concave cutout at the bottom of the trigger, which has
  • side-to-side grooves like the edge of a dime
  • Height
  • Upper portion: 7/16"
  • Lower portion
  • To the center: 3/4"
  • To the outside edges: 7/8"
  • Total height
  • To the center of the cutout: 5/32"
  • To the outside edges: 1-5/16"
  • Depth
  • Upper portion: 1-5/64" (BETWEEN 1-1/16" AND 1-3/32")
  • Lower portion: 1-1/64"
  • Thickness
  • Upper portion: 9/16"
  • Lower portion: 11/32"
  • Padlock hole dia: 3/8"
  • Mounting hole - has a round, recessed area on each side
  • before the mounting hole starts
  • Recess
  • Dia: 5/16"
  • Depth: 3/32"
  • Mounting hole
  • Dia: 1/8"
  • Depth: 3/8"
Customer Reviews
(0.00)
# of Ratings: 0
There are no comments for this product.