Quickship
Republic Storage Systems, LLC
Republic Locker RH Lift Only for Recessed Locker Door Handle Assembly
- SKU:
- RS-2008-RH
- MFG Part #:
- 7137185
DESCRIPTION
Slide plate mechanism for Republic Steel recessed handle cup.| Material | : Steel |
| Thickness | : 1/16" |
| This item is a piece of steel with cutouts and 90 degree bends in it. As the piece faces you, with three of the four bends facing you one | |
| bend facing away from you, it consists of the following | : |
| - A mounting side on the left, which is bent forward and has an | |
| upper portion, a lower portion, and a cutout gap between. | |
| Each portion has a finger tab, which fits into and secures the | |
| lift onto the lockbar | |
| - A back portion | |
| - A tab on the top right, which is bent forward and provide a place | |
| to mount the plastic trigger | |
| - A tab on the bottom right, which is bent back and has a squared | |
| cutout for the combination lock bolt to rest in when it's in the | |
| locked position. The square cutout continues into part of the | |
| back portion. | |
| Height of lift | : 4-5/16" |
| Left side mounting portions | |
| Top portion | |
| Height | : 1-/16" |
| Depth | : 1-1/16" |
| Finger tab | |
| Width | : 1/8" |
| Length | : 1/4" |
| Bottom portion - is deeper at the top than the bottom | |
| Height | : 1-21/32" |
| Depth at top | : 1-5/16" |
| Depth at bottom, where finger tab is | : 1-1/6" |
| Finger tab - goes left off the bottom portion, then takes a | |
| 90 degree bend to point down. | |
| Length of left portion | |
| At inside corner | : 3/32" |
| At outside corner | : 1/4" |
| Length of down portion | |
| At inside corner | : 3/32" |
| At outside corner | : 1/4" |
| Back portion | |
| Height | : 4-5/16" |
| Width | |
| At top, where top left portion and right plastic trigger | |
| mounting are is | : 2-17/32" |
| At middle | : 1-3/8" |
| At bottom, including lower left portion and right lock | |
| cutout tab | : 1-19/32" |
| At bottom, up to, but not including lock cutout | : 1-1/16" |
| Lock cutout | |
| Height | : 7/8" |
| Width | : 7/16" |
| Right portions | |
| Top tab for plastic trigger mount | |
| Height | : 1-1/6" |
| Depth top is narrower than the bottom | |
| To top | : 5/8" |
| At bottom | : 1-3/16" |
| Padlock hole | |
| Dia | : 3/8" |
| Distance of hole from bottom of tab | : 3/16" |
| Distance to hole from back of tab, where it joins the | |
| back plate | : 11/16" |
| There is a small finger tab that is lifted out of the surface of | |
| the right side of this portion about 40 degrees, and, as you | |
| face it, goes in a direction of about a 2 | : 00 position on a clock. |
| The plastic trigger snaps down over this. | |
| Width | : 5/32" |
| Length | : 7/32" |
| Height off surface | : 1/8" |
| Bottom tab with lock cutout | |
| Height | |
| Outside | : 1-13/16" |
| Inside | : 7/8" |
| Depth | |
| Outside | : 23/32" |
| Inside | : 71/6" |
Questions about Republic Locker RH Lift Only for Recessed Locker Door Handle Assembly?
Please contact us with any questions you have about Republic Locker RH Lift Only for Recessed Locker Door Handle Assembly and we'll be in touch.
Related Products
Quickship
Quickship
Quickship
Quickship
