Quickship
DESCRIPTION
Replacement right hand lift handle for Lyon locker, use with recessed handle LY2237.| Material | |
| Slide lift | : Steel |
| Finger lift | : Black nylon |
| This item is a piece of steel with cutouts and 90o bends in it. | |
| As the piece faces you, with two bends pointing towards you and | |
| one bend pointing away from you, it consists of the following | : |
| - A lockbar mounting side on the left, which is bent forward and | |
| has two triangular tabs, bent out to the left, which snap into | |
| the lockbar, and a single mounting hole between them | |
| - A back portion, which is wider on the top than the bottom | |
| - An upper right section, which bends facing you, and has an | |
| oval padlock hole. The nylon finger lift, which also has an | |
| oval padlock hole in it, snaps over this section. | |
| - A lower right lock stop tab, which bends facing away from you. | |
| This tab acts as a stop for the bolt on a combination lock, | |
| and the lift can not go up until the bolt is turned in | |
| and out of this tab's way. | |
| Height of lift | : 5-1/8" |
| Left mounting portion | |
| Depth | |
| Top and bottom | : 1" |
| By mounting tabs | : 1-3/16" |
| Tabs | |
| Qty | : 2 |
| Width | : 5/16" |
| Height off surface | : 3/16" |
| Mounting hole | |
| Qty | : 1 |
| Shape | : Slightly oval |
| Height | : 13/64: (between 3/16" and 7/32") |
| Width | : 15/64" (between 7/32" and 1/4") |
| Back portion | |
| Width | |
| At top | : 2" |
| At bottom | : 15/16" |
| Height of upper section | : 1-7/16" |
| Right portions | |
| Top tab (underneath nylon lift finger) | |
| Height | : 1-7/16" |
| Depth | : 1-1/32" |
| Padlock hole | |
| Shape | : Oval |
| Height | : 3/8" |
| Depth | : 1/2" |
| There is a round dimple that the lift snaps over | |
| Dia | : 3/16" |
| Height off surface | : 1/8" |
| Nylon finger lift - the front edge is wider and longer than the | |
| rest of the finger lift. As it faces you, the shape resembles | |
| an arrow pointing down - wide at the top, like arrow feathers, | |
| becomes narrow in the middle, then wide again, angling down | |
| to a soft point at the bottom. The finger lift is slotted in | |
| the back to fit over the steel tab on the slide lift. | |
| Height | |
| In front | : 1-3/4" |
| In back | : 1-1/2" |
| Width | |
| In front | : 9/16" |
| In back | : 1/4" |
| Depth | |
| Upper front portion | : 3/16" |
| Lower front portion | : 7/16" |
| Upper back portion | : 27/32" |
| Lower back portion | : 19/32" |
| Padlock hole - oval | |
| Height | : 7/16" |
| Width | : 17/32" |
| Bottom tab / lock stop | : |
| Height | : 1-1/4" |
| Depth | : 11/32" |
Questions about Lyon Locker RH Recessed Lift, 1988 to Present?
Please contact us with any questions you have about Lyon Locker RH Recessed Lift, 1988 to Present and we'll be in touch.
Related Products
Quickship
Quickship
Quickship
Quickship
