Quickship
Allegion
Cast Brass Square Door Holder, Plunger-Style with Aluminum Finish
- SKU:
- GJ1153M
- MFG Part #:
- FS1153 US28
DESCRIPTION
Ingersoll Rand's Cast Brass Square Door Holder has an attractive satin aluminum finish. The plunger activates with minimal pressure and releases with a tap on the platform lever. The plunger and internal parts are constructed of plated steel for years of use. The replaceable, non-marring rubber shoe will not cause damage to your floors.| Material | |
| Housing | : Cast aluminum with US28 Satin Alum finish |
| Plunger | : Steel top half, cast aluminum bottom half |
| Platform lever | : Steel |
| Bumper | : Gray, non-marking rubber |
| Housing | |
| Height | : 2-25/32" |
| Width | : 1-3/8" |
| Depth | : 1-3/8" |
| Thickness | : 1/16" |
| Mounting plate | |
| Width | : 1-3/8" |
| Height | : 6-3/16" |
| Thickness | : 5/32" |
| Mounting holes | |
| Qty | : 2 |
| Type | : Countersunk |
| Hole to hole OC | : 5-1/2" |
| Plunger - upper half is a round, steel post. | |
| Lower half is a square, aluminum post | |
| where it connects to the bumper plate. | |
| Upper half | |
| Diameter of foot platform | : 3/4" |
| Post diameter | : 1/2" |
| Length, when bumper is fully retracted | : 2-3/32" |
| Lower half | |
| Width | : 13/16" |
| Depth | : 13/16" |
| Length, when bumper is pushed all of the way down, | |
| not including bumper plate | : 21/32" |
| Length from top of plunger to bottom of bumper | : 5-11/16" |
| Platform lever | |
| Width | : 1-3/8" |
| Depth | : 1-3/16" |
| Thickness | : 3/32" |
| Bumper | |
| Shape | : Rectangular |
| Width | : 31/32" |
| Length | : 1-1/4" |
| Thickness of exposed material when bumper is installed | : 7/16" |
| The top of the shoe is molded so as to form a rectangular | |
| platform, narrower than the rest of the bumper, | |
| but the same length. This 'male plut' fits into | |
| a female counterpart on the bottom of the plunger section | |
| of the door holder. | |
| Width | : 11/16" |
| Depth | : 1/8" |
| Height | : 1/8" |
| Tread | |
| Type | : Four square-edged treads running the |
| length of the bumper | |
| Width of each | : 3/32" |
| Depth | : 5/32" |
| Bumper mounting plate (attached to bottom of plunger) | |
| Outside | |
| Width | : 1-11/32" |
| Depth | : 1" |
| Thickness | : 1/4" |
| Inside | : There is a rectangular recessed area on the |
| bottom of the plate. The rubber bumper has a male | |
| rectangular raised area that fits into this. | |
| Width | : 1-1/4" |
| Length | : 3/4" |
| Depth | : 1/8" |
| Mounting hardware (included) | |
| For door holder | |
| Qty | : 2 |
| Type | : #8 x 1" Phillips flat head sheet metal screw |
| For bumper | |
| Qty | : 1 |
| Type | : #8 x 3/4" Phillips flat head sheet metal screw |
| Operating information | |
| Distance of 'throw' - the difference of distance from | |
| the bottom of the bumper and the surface of the floor | |
| when the post is fully retracted | : 1-5/8" |
| Distance between the bottom of the bumper and the bottom | |
| of the door when the post is fully retracted | : 9/16" |
Questions about Cast Brass Square Door Holder, Plunger-Style with Aluminum Finish?
Please contact us with any questions you have about Cast Brass Square Door Holder, Plunger-Style with Aluminum Finish and we'll be in touch.
Related Products
Quickship
Quickship
Quickship
Quickship
