Quickship
Republic Storage Systems, LLC
Locker LH Lift Only for Recessed Locker Door Handle Assembly, compatible with Republic locker handle
- SKU:
- RS-2009-LH
- MFG Part #:
- 2146
DESCRIPTION
Republic Locker LH Lift Only for Recessed Locker Handle Assembly.| Material | : Steel |
| Thickness | : 1/16" |
| This item is a piece of steel with cutouts and 90o bends in it. | |
| As the piece faces you, with three of the four bends facing you | |
| and one bend facing away from you, it consists of the following | : |
| - A mounting side on the right, which is bent forward and has | |
| two finger tabs - one near the top outside corner and one at | |
| the bottom outside corner | |
| - A back portion | |
| - A tab on the top left, which is bent forward | |
| and provides a place to mount the plastic trigger | |
| - A tab on the bottom left, which is bent back | |
| and has a squared cutout for the combination lock bolt | |
| to rest in when it is in the locked position. The square | |
| cutout continues into part of the back portion. | |
| Height of lift | : 4-5/16" |
| Right side mounting portions | |
| Top portion | |
| Height | : 1-1/16" |
| Depth | : 1-1/16" |
| Finger tab | |
| Width | : 1/8" |
| Length | : 1/4" |
| Bottom portion - is deeper at the top than the bottom | |
| Height | : 1-21/32" |
| Depth | |
| At top | : 1-5/16" |
| At bottom, where finger tab is | : 1-1/16" |
| Finger tab - goes to the right off the bottom portion | |
| then takes a 90o bend to point down | |
| Length of rightward portion | |
| At inside corner | : 3/32" |
| At outside corner | : 1/4" |
| Length of downward portion | |
| At inside corner | : 3/32" |
| At outside corner | : 1/4" |
| Back portion | |
| Height | : 4-5/16" |
| Width | |
| At top, where top right portion and | |
| left plastic trigger mounting area is | : 2-17/32" |
| At middle | : 1-3/8" |
| At bottom, including lower right portion and | |
| left lock cutout tab | : 1-19/32" |
| At bottom, up to, but not including lock cutout | : 1-1/6" |
| Lock cutout | |
| Height | : 7/8" |
| Width | : 7/16" |
| Left portions | |
| Top tab for plastic trigger mount | |
| Height | : 1-1/16" |
| Depth - top is narrower than the bottom | |
| At top | : 5/8" |
| At bottom | : 1-3/16" |
| Padlock hole | |
| Dia | : 3/8" |
| Distance to hole from bottom of tab | : 3/16" |
| Distance to hole from back of tab, where | |
| it joins the back plate | : 11/16" |
| There is a small finger tab that is lifted about 40o | |
| out of the surface of the left side fo this portion | |
| and goes in a direction of about a 2 | : 00 position |
| on a clodk as you face it. The plastic trigger | |
| snaps down over this finger. | |
| Width | : 5/32" |
| Length | : 7/32" |
| Height off surface | : 1/8" |
| Bottom tab with lock cutout | |
| Height | |
| Outside | : 1-13/16" |
| Inside | : 7/8" |
| Depth | |
| Outside | : 23/32" |
| Inside | : 7/16" |
Questions about Locker LH Lift Only for Recessed Locker Door Handle Assembly, compatible with Republic locker handle?
Please contact us with any questions you have about Locker LH Lift Only for Recessed Locker Door Handle Assembly, compatible with Republic locker handle and we'll be in touch.
Related Products
Quickship
Quickship
Quickship
